High quality car ignition coil provider

Top rated ignition coil supplier: These multiple-coil-pack-systems are much more reliable than the distributors of the past, but individual ignition coils can still fail over time and lead to an engine misfire condition. When a cylinder misfires, that means the fuel inside it is not burning at the correct time or not burning at all. This is also sometimes referred to as a dead cylinder. Prolonged misfiring can lead to larger problems like warped piston rods or corrosion inside the cylinder wall. It can also cause unburned fuel to leak into your exhaust system, which is bad for the environment and worse for your car’s catalytic converters. Once identified, a misfire should be addressed as soon as possible. See more information on ignition coil manufacturers.

The automotive ignition coil consists of an electrically-conductive wire wound into a helix, usually around a magnetic core. When power is applied across the two coils, it produces an electrical field that generates an electromagnetic field that induces currents in the secondary winding of the coil. This high voltage is then stepped down by one or more stages before being applied to the spark plug. There are three different types of car ignition coils: Single-coil systems use one coil per cylinder. Dual-coil systems use one coil per cylinder, but they are wired in series so that each fires twice for every cycle of the power supply. In this way, it’s possible for both coils to fire at once, improving efficiency and reducing wear on the engine by giving it more time between firings.

To put it simply, the ignition coil is a transformer, which increases the voltage of tens of volts to tens of thousands of volts, but the voltage input to the primary coil is provided by an electronic igniter. The reason why the ignition coil burns out. Ignition coil burnout is mainly caused by the ageing and breakdown of the insulation layer or the damage of the switching transistor. The large gap between the spark plugs will cause the main coil to load, heat, and age quickly. The small gap between the spark plugs will cause the secondary coil to discharge current, heat, and insulation. Fast, the assembled car coil may have a shorter lifespan, such as poor insulation material durability, the large internal resistance of the coil, high heat generation, and low quality of the tertiary tube. Ignition coil manufacturer has more than 30 years of production experience.

The primary winding of an ignition coil will typically contain 150 to 300 turns of wire; the secondary winding will typically contain 15,000 to 30,000 turns of wire, or around 100 times more than the primary winding. The magnetic field is initially created when the vehicle’s electrical system applies approximately 12 volts to the ignition coil’s primary winding. When a spark is required at a spark plug, the ignition system will switch off the current flow to the primary winding, which will cause the magnetic field to collapse. The collapsing magnetic field will induce a voltage into the primary winding in the region of 200 volts; but the voltage induced into the secondary winding will be approximately 100 times greater, around 20,000 volts.

The first coil-based ignition system is credited to the American inventor Charles Kettering, who developed a coil ignition system for a major vehicle manufacturer around 1910/1911. For the first time, he devised an electrical system that powered the starter motor and ignition at the same time. The battery, a generator and a more complete vehicle electrical system provided a relatively stable electrical supply to the ignition coil. The Kettering system used a single ignition coil to produce a high voltage, which was passed to a rotor arm that effectively pointed the voltage to a series of electrical contacts located in the distributor assembly (one contact for each cylinder). These contacts were then connected by spark plug wires to the spark plugs in a sequence that made it possible to distribute the high voltage to the spark plugs in the correct cylinder firing order.

The hardware accessories series is available in a wide range of types and specifications. Haiyan hardware accessories manufacturer carries out strict quality monitoring and cost control on each production link of hardware accessories, from raw material purchase, production and processing and finished product delivery to packaging and transportation. This effectively ensures the production of hardware accessories manufacturer has better quality and more favourable prices than other products in the industry. Discover extra information on hj-auto.com.

Haiyan aijian Co.Ltd. is a car ignition coil manufacturer, which are seated on No.338 Yanjia Road, Wanghai Haiyan Jiaxing, Zhejiang, locating western Hangzhou bay cross-sea bridge,3.5 KM far from the Zhajiasu high way exit,1.0 km distance from Huangpu high way exit, convenient transportation, is the centre of economic of shanghai-Ningbo-Hangzhou triangle. The main products of Haiyan wholesale automotive ignition coil manufacturers contain car ignition coil pack, plug coil, spark coil, tool cabinet, hardware accessories, and precision matching pieces of Japanese host, every year manufacturing ignition coils 1,000,000 PCS, cars pare parts 2,000,000 sets,3,000,000 sets of Japanese hosts accessories. Widely export to South and North America, Europe, South Africa, and Asia.